W/E 10th October 2017


Man down!

First post in a while but I’ve not been idle…

The Scottish Rally report can be found over in the Trips section – pleased that the Atlas managed to complete all three National Rallies giving me another ‘Three Nations Award’ to put in the cabinet πŸ™‚

So back to most recent times. Friday evening on my way home and I’m rear ended by a young lady. Bike got pushed away from me and went down on the left side and I simply stepped off it. The damage is limited to bent bars, clutch lever, broken number plate, scratched front mudguard and maybe the rear mudguard (tho’ this seems to have popped straight being plastic). In addition its been out with the big hammers to straighten the pannier frame and gear change lever. I guess these things happen.


I’ve gone back to running a non o ring chain on the Atlas. The chain needed replacing after the Scottish’ and I had a non o ring in the shed. I also wanted to try it out as of course it is considerably lighter than the o ring equivalent and I’m hoping it will put less wear on the chocolate gearbox output shaft.

Immediate impression was how much lighter it is in operation. I’m not that sensitive but the connection to the back wheel does feel, well, lighter! To back up the new chain I’ve invested in some chain wax. I’ve boiled the chain once (started it off in the kitchen but Mrs A chased me out into the garden) to try and get grease in to the links. I’ll suspend judgement as to whether this extends the life of the chain. The problem with the chain is that it does need more adjustment – if I was to go touring with Mrs A I think I’d spin an o ring on for the tour and maybe revert back for solo use. Seems like a lot of messing about but the gearbox output shaft isn’t something that can be easily fixed once worn.


Clee Hill

Took the Atlas out for a ride to Clee Hill, Shropshire with Catherine on her Ducati. The roads through Ledbury and then out to Bromyard and Stourbridge are blinding. As you can see Clee Hill gives spectacular views.

However nothing is ever straightforward and stopping for petrol in Leominster saw the Atlas clutch cable break – my tools and spare cable were in my panniers which I’d removed and left in my shed…(arse)! So nothing for it but to plot a route involving the minimum number of junctions get a shove and bang it into first and be off. Lucky the roads to the M50 are quiet and with a splash and dash stop for petrol I managed to ride the 140 miles home trouble free.


Not even close…

The trouble began when I arrived home and set about sorting out the cable. I had a brand new cable but as you can see the handlebar nipple was too big as it turned out was the outer sheath end caps. So the new inner was threaded through the old outer and the original nipple pressed in to action (fortunately the Atlas only has a detachable nipple on one end of the cable). I’m ashamed to say this new cable was supplied to the German dealer by the UK’s very own Venhill…British quality, need I say more.

The clutch problem though does have a happy ending in that it prompted me to pay more attention to cable adjustment. I found that the cable not only adjusts at the handlebar but also there is a screw onto the clutch pushrod down in the engine case. I turned this all the way out and then back in to get the right amount of free play at the bar and it seems to have gone a long way to solve the clutch slip problem πŸ™‚ I think that the engine adjuster was pressing on the pushrod so whatever I did at the bars it was always going to slip. The extent of the ‘fix’ has been further highlighted by the use of unbranded 20/50 oil which has not induced any slip!

The clutch return spring is worn out again. It’s a simple matter of ‘pre-loading’ the change with an additional tap. It can be bothersome in heavy traffic when you’d ideally like it to cut down through the box before coming to a halt but it isn’t so bad I’ll be fixing it anytime soon! I know however from experience this is a warning that sometime in the future it will stop returning without a lot of ‘pre-loading’ so I’ll add some springs to parcel that will be arriving from Germany with ‘crash damage’ goodies…

I fitted and did a ‘prototype’ test on a Malcolm Cox silencer – very impressed πŸ™‚ The silencer went straight on to the standard front pipes and collector and sounds just like the original (quiet)…which has the effect of making me ride the bike faster!

On speed I got a letter from the Police to tell me that I can attend a ‘driver education’ course in lieu of points on my license for the indiscretion in Wales (see Trips) while visiting the ILOC rally. Still cost me Β£91 but for this I get an afternoon out in Shepperton by the Thames and the chance to mingle with other deviants…no doubt I will end up on the ‘Group W’ bench!

I’ve now done 1500 miles on it and it’s looking good – the back of the silencer gets covered in road filth and so far the finish is holding up fine. I’m not sure whether to take this off and refit in the summer before road salt starts being spread – not that I doubt the finish but any silencer fitted in this location is going to get a hard time and why waste it when I don’t have to?

This second picture shows the prototype front mounting was a little short but I know Malcolm changed this. The shape of the box is just as the original though with slightly less definition in the pressing (this though cannot be seen behind the panel). The lugs are there for the rubber bungs to keep the panel off the box – I cable tied some tap washers on the back one to keep the mudguard panel off the silencer. All in all the work that Malcolm has done in creating the complete system (left hand bend pipes as on the Mk 3) is great news for Atlas owners who can now get a top class, hand made, replacement that is better than standard!

Finally Harley Davidson have coughed up for the battery that failed after 18 months. The warranty manager was quite graceless and I suspect would be a bully to work for so nil marks for their customer service – but it must be said the Sportster battery is great for the Atlas…and 18 months and therefore 30,000 miles ain’t too shabby!

Nick πŸ™‚


One thought on “W/E 10th October 2017

  1. Didn’t know you could still get that chain wax – I still have a tin in the garage somewhere. Wifey didn’t like me using the kitchen stove either…..
    No reason why a standard chain should not be OK for solo use – as you will remember back in the dark ages that was all we had to use, and my old Commando went many a mile with one and probably had about the same power and weight as the Atlas. Current Cagiva uses a 525 o-ring so it is spray only for that.
    Keep up the good work – I always enjoy reading your exploits, even though you have put me off wanting a Laverda twin!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s